The dock is not the only place in your business where lifts and levelers might be useful. Help save back injuries with Dock and In-Plant lifts. Our Serco line lifts, tilts, and turns to help your team perform a variety of tasks efficiently without hurting themselves.
Dock and In-Plant Lifts
Located in Jacksonville, Orlando & Tampa, FL
Serco Level Lift Model
Benefits
High-performance dock leveler — it provides the same performance benefits of a hydraulic dock leveler such as regenerative hydraulics, powered lip control, safety velocity fuse and push-button controls.
Below-dock operation — In scissor mode, it eliminates the steep grade differences between the vehicle bed and the leveler deck, providing safe, level, below-dock operations.
Scissors lift versatility — Unlike standard scissor lifts, the hydraulically powered dock lip ensures faster cycling times and its lifting capacity can handle the toughest loads while also providing dock-to-grade-level forklift access
Design Highlights
- 50,000 lbs. Capacity Leveler (per ANSI MH14.1-1987)
- 12,000 lbs. Capacity Lift (8 ft. long units)
- 20,000 lbs. Capacity Lift (10 & 12 ft. long units)
- 18″ Lip Standard
- LED Light Communication Package
- Remote 7.5 HP Independent Lift Motor & Hydraulic System
- PLC Operation
- 1 HP Independent Leveler Motor & Hydraulic System
- Full Feature NEMA 12 Control Panel with Mushroom Style Stop Button
- Remote NEMA 4X Pendant Push Button Hand Control
- Interior Warning Light & Audible Alarm Indicate Dock Lift Is Not In Stored Position
- Safety Velocity Fuse on Leveler and Lift
- Guard Rail Package
- Rear Hinge Blocks
- Protective Roller Curtain on Front
- Side and Rear Weatherseal
- Grease Fittings
Serco Rail Lift Model
Design Highlights
- Low Profile for Surface-mounted Applications z No Pit Construction Required
- Three-sided Platform
- Heavy-duty I-beam Deck Understructure
- Excellent End-load Stability in Fully Raised Position z Displacement style Cylinder with Internal Stops
- Self-contained Power Unit/control Panel
- Standard Pre-wired Control Panel
- NEMA 4X Push-button Controller with 15’ Cord
- Superior Speed-to-horsepower Ratio Compared to Scissor-style Dock Lifts
- Direct thrust Cylinders Provide Constant Speed Through Full Range of Travel
- Checker Plate or Smooth Deck Surface z Sealed Guide Bearing Rollers
- Fused 24-volt Control Circuit
Serco Loadwarrior Air Lift Model
Design Highlights
- No lag down, portable design
- Pallet jack pockets built in
- Removable gibs
- Over-pressure relief valve
- Operating angle from horizontal to 30 degrees from horizontal
- Heavy-duty airbag
- Downspeed flow control
- Works on “shop air,” 80psi
- Includes a hand or foot valve control and a 6′ hose
- Meets or exceeds the ANSI MH29.2 standard for industrial scissor lift
Serco Loadwarrior Turntable Model
Manual or powered models are available to efficiently palletize, build-up and break-down, and either can be mounted on a scissors lift, stable bench, or other surface. In addition, ground-mounting is also available.
Design Highlights
- Rigid base frame with predrilled mounting holes
- 1/2″ thick steel platform with rounded corners
- Tough TGP hard-chromed kingpin
- Rollers are sealed ball bearings for ease of operation
- Roller-pin bushings are self-lubricating
- 34″ x 34″ is minimum turntable size
Serco Scissors Dock Lift Model SDL68-5
Our Dock Lifts can accommodate a wide variety of truck styles; from 20″ step vans or pick-up trucks to high cube vans, standard semi-vehicles and 60″ high stake bed vehicles. They can be pit or surface-mounted inside the building or in front of the loading dock. (Surface-mounted dock lifts can be relocated if used in applications where a pit or permanent installation is prohibited.)
Design Highlights
- Beveled toe guards
- 18″ standard solid or split bridge plate
- Dual hydraulic lifting cylinders for optimum performance
- Velocity fuses on lift cylinders prevent uncontrolled descent
- Removable, mandrel-formed tubing handrails
- Maintenance safety strut
- Safety tread steel deck
- Safety chains across operating ends
- Upper travel limit switch
- Available in 4,000-20,000 lb. capacities
Serco Loadwarrior Double Scissors Table Model
Design Highlights
- Pre-wired power unit with UL approved control components
- Internally mounted 5 hp power unit
- Self-lubricating composite bearings
- Solid steel legs with stiffener bars
- Turned, ground, polished and hard-chromed axle pins
- Double-wire braided hydraulic hoses
- Velocity fuses on all cylinders to prevent uncontrolled descent
- Polyethylene reservoir allows easy visual check of oil level
- Maintenance locks built into base frame
- Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
Serco Loadwarrior Tilter Model
Design Highlights
- Pre-wired power unit with UL approved control components
- Power unit internally mounted
- Available in 1 1/2 hp three-phase or 3/4 hp single-phase with 24V AC control valve
- Self-lubricating composite bearings
- Velocity fuses on all cylinders to prevent uncontrolled descent
- Double wire braided hydraulic hoses
- Polyethylene reservoir allows easy visual check of oil level
- Maintenance locks built into frame
- Standard 12′ high lip
- 28″ W x 38″ L minimum platform size
- Meets or exceeds the ANSI MH29.2 standard for industrial tilters
Serco Loadwarrior Scissor Table Model
Design Highlights
- Solid steel legs with stiffener bars for extra strength and support
- Polyethylene tank prevents condensation, provides easy check of oil level
- High-pressure cylinders with safety velocity fuses to prevent uncontrolled descent
- Pre-wired NEMA-rated controls
- High-strength roller pins with snap rings
- Hardened steel rollers
- High-strength steel polished axle pins
- UL-approved control components
- Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
Serco Loadwarrior Air Tilter
Design Higlights
- Reinforced, heavy-duty airbag
- Air damper reduces platform bounce
- Fork pockets for simple mobility
